About Reaction Vessels
KGW-ISOTHERM manufactures about 400 different types of reaction vessels made of glass in series. The reaction vessels are produced with a volume from 250 ml up to 20 litres with flat bottom, round bottom or bumped boiler end. As closing, laboratory flange with O-ring groove according to DIN 12214 is used. The bottom-outlet is available as standard with two different valves, the laboratory valve "L" (spindle is pressed while turning, type Torion) and the industrial valve "J" (spindle is springloaded and regulates herself), and the spherical ground joint S40. Every valve in the reaction vessels is dead volume free.
Bottom Outlet
Industrial J-valve 10mm
The industrial valve is a dead volume free PTFE spindle valve with sloped outlet.
The spindle shall be pressed in without turning. In the valve housing is an additional spring mounted in.
So the spring pressure of the spindle to the valve seat can be increased spring-loaded and the
spindle regulates herself. This guarantees a good tightness at large variations of temperature.
temperature range: -80°C to +200°C
J-valve 10mm
J-valve 10mm in
cross-section
Industrial J-valve 20mm
The industrial valve is a dead volume free PTFE spindle valve with sloped outlet.
The spindle shall be pressed in without turning. In the valve housing is an additional spring mounted in.
So the spring pressure of the spindle to the valve seat can be increased spring-loaded and the
spindle regulates herself. This guarantees a good tightness at large variations of temperature.
temperature range: -80°C to +200°C
J-valve 20mm
J-valve 20mm in cross-section
Laboratory Valve L
The laboratory valve is a dead volume free PTFE spindle valve with the spindle being pressed in while turning. the valve has an 10mm bore-hole.
temperature range: -10°C to +120°C
L-valve 10mm
L-valve 10mm in cross-section
Industrial J-valve 10mm with internal PT100
The industrial valve is a dead volume free PTFE spindle valve with sloped outlet.
The spindle shall be pressed in without turning. In the valve housing is an additional spring mounted in.
So the spring pressure of the spindle to the valve seat can be increased spring-loaded and the
spindle regulates herself. This guarantees a good tightness at large variations of temperature.
temperature range: -80°C to +200°C
connection: Lemo 0
J-valve 10mm with PT100
J-valve 10mm with PT100 in cross-section
Industrial J-valve 20mm with internal PT100
The industrial valve is a dead volume free PTFE spindle valve with sloped outlet.
The spindle shall be pressed in without turning. In the valve housing is an additional spring mounted in.
So the spring pressure of the spindle to the valve seat can be increased spring-loaded and the
spindle regulates herself. This guarantees a good tightness at large variations of temperature.
temperature range: -80°C to +200°C
connection: Lemo 0
J-valve 20mm mit PT100
J-valve 20mm with PT100 in cross section
Industrial J-valve 10mm pneumatic
The industrial valve is a dead volume free PTFE spindle valve with sloped outlet.
The spindle shall be pressed in without turning. In the valve housing is an additional spring mounted in.
So the spring pressure of the spindle to the valve seat can be increased spring-loaded and the
spindle regulates herself. This guarantees a good tightness at large variations of temperature.
temperature range: -80°C to +200°C
working pressure: 2,5 - 3 barÜ
max. pressure 4 bar
Control unit for pneumatic valve on request
J-valve 10mm pnematic betätigt
J-valve 10mm mit PT100 pneumatic betätigt
Connection variants at the drain
Addition of a special connection to any valve
Variants: GL18, GL25, DN15 or DN25
Temperature range GL: -10 ° C to + 120 ° C
Temperature range DN: -80 ° C to 200 ° C
J-valve 10mm with GL18
J-valve 10mm with DN15
Spherical Ground Joint 40
According to DIN 12244 (Part 1)
Spherical Ground Joint 40
Thermal Jacket Connections
Thermal Jacket connections are available in two versions:
Thermal Jacket Connection GL18 Olive
For temperatures up to +100° C
Thermal Jacket Connection DN15 Flange
For temperatures up to +300° C
Versions other than those described are always available. On request we can supply you with a professional overview of our products per CAD drawings.
All reaction vessels even the standard types are produced on customer instruction. Therefore often changes in couplings or flanges will be offerd without additional cost.
Use Our Configuration Wizzard for Reaction Vessels.